Ez dock coupler installation tool

Ez dock coupler installation tool DEFAULT

Coupler installation tool

This tool simplifies installation, allowing the user to assemble docks with EZ Dock couplers without getting in the water.

After much research and many months of investigation, it was clear that the EZ Dock was the clear selection for our eight boat slip marina plus the additional space for our Personal Water Craft, etc. – Greg Evans, Smithfield, NC, Lakeside Point Dock MasterMore Testimonials
EZ Dock, Inc. is a PlayPower, Inc. company. © 2021 PlayPower, Inc. All rights reserved.
We us cookies to improve your browsing experience! By continuing to use this website, you agree to the terms outlined in our Privacy Policy, and to the receipt of targeted communications through our marketing platforms. We do not sell your personal information, and only obtain personal information with your consent. For more details, please refer to our Privacy Policy.
Check out our new EZ Port 280 -- the widest port on the market. Now available for pre-orders! Learn More
Sours: https://www.ez-dock.com/product/coupler-installation-tool/

Ez dock installation tool

Filter Type:All TimePast 24 HoursPast WeekPast month

Listing Results Ez dock installation tool

Coupler Installation Tool EZ Dock

8 hours ago 45" X 12" X 1". Description. This tool simplifies installation, allowing the user to assemble docks with EZ Dock couplers without getting in the water. DESCRIPTION. We installed our EZ Dock system in February 2008 and have been extremely pleased …

Show more

See Also: Ez dock dog bone couplerShow details

EZ Dock Custom Residential & Commercial Floating Docks

4 hours agoEZ Dock has been around since 1991, helping industrial, commercial, government and residential clients get better access to the water. We design all of our products to be fully customizable. Whether you need a commercial-grade dock to run boat tours, a EZ Launch® Residential, or a swimming dock

See Also: Ez dock 2i installShow details

Owner’s Manual And Installation Instructions EZ Dock

2 hours agoEZ Dock in-water installation tool (9000010) 1/2” drive ratchet and socket set Open-end and boxed-end wrench set Screwdrivers (Phillips and standard) Adjustable wrenches Hammer, level, utility knife and pliers. 5 . EZ Dock Specifications.

Show more

See Also: Ez dock assemblyShow details

EZ Dock In Water Installation Tool SS FWM Docks & EZ

4 hours ago FWM Docks EZ Dock In Water Installation Tool - SS. a leading manufacturer of stationary docks, rolling dock and floating dock systems for residences, parks and marinas.

Brand: FWM Docks

Availability: In stock

Show more

See Also: Ez dock coupler installation toolShow details

* Welcome To EZ Dock Long Island Your Suffolk And Nassau

3 hours ago Welcome to EZ-Dock Long Island @ Mariner's Cove Marine * 631.728.0286 : We are a full service marina located on the Shinnecock Canal, on Long Island, as well as a 8+ acre facility with indoor and outdoor showroom space. We also have sales and service facilities conveniently located in Staten Island, NY. We have 30 years experience in the marine

Show more

See Also: Ez dock coupler toolShow details

Inwater Installation Tool 9000010SS EZDock

Just Now Introducing EZ Dock’s newly revised in-water installation tool. These new revisions to the current 9000010 include the removal of the bent foot portion for easier use. This change will allow the user to remove the tool at the coupler pocket and not have to travel back along the seam for tool removal. These new tools are

Show more

See Also: Ez dock couplerShow details

Removal Of Docks In Ice Conditions Home Of EZ Dock Gulf

6 hours ago Removal of Docks in Ice Conditions Your don’t have to… Ice has no affect on the EZ Dock System. Since an EZ Dock requires only an inch of water to float, the docks will “pop” to the top of the ice when the water freezes, much like an ice cube tray.

Show more

See Also: Ez dock manualShow details

EZ Dock (Dock Accessories) • Marine Dock & Lift

5 hours agoEZ Dock Accessories Bumper and Handrail Post EZ Dock Nylon Tie up Cleat with Screws Cleat Corner Gusset Coupler Set In Water Installation Tool Dock Bumper – Short Style EZ Dock Bench with Armrests EZ Dock Corner Box EZ Dock Poly Ladder Gangway to EZ Dock In Water Installation Tool with Bottom Coupler Kayak Launch…

Show more

See Also: Easy dock installationShow details

EZ DOCK Installationsfilm YouTube

3 hours agoEZ Docks offers a wide selection of dock systems, boat and PWC lifts, and accessories. It combines strength and stability with light weight and low maintenan

Author: HAGSGlobal

Views: 12K

Show more

See Also: Doc ConverterShow details

EZ Dock Components Accessories Tools

7 hours ago Accessories Tools. In-Water Installation Tool #9000010 Coupler installation tool simplifies in water installation of couplers. Composite Coupler Installation Tool #900005. Dock Wheels #900050 Steel frames with polyethylene wheels make movements of docks easier. (Sold in pairs).

Show more

See Also: Doc ConverterShow details

EZ Trail™ Installation Instructions EZ Dock

9 hours ago Do not attempt in-water installation without EZ Dock in-water coupler installation tools. DANGER Figure 3 1. Align and butt the adjoining ends of the dock sections . 2. Insert the bottom coupler and bolt assembly onto the in-water installation tool, firmly pulling up to seat coupler. 3.

Show more

See Also: Doc ConverterShow details

Ez Dock Coupler Installation Tool About Dock Photos

8 hours agoInstallation instructions coupler installation tool ez dock texas installation instructions to have fun boat explore installation instructions. Coupler Installation Tool Ez Dock. Coupler Tool Ez Docks Marine Construction. Drive Tool 15 16 Socket Adaptor Ez Dock.

Estimated Reading Time: 3 mins

Show more

See Also: Doc ConverterShow details

EZ Dock Owners Manual EZDockInventory.com

8 hours ago performing in-water installation of docks, ports and couplers can result in accidental drowning and death. Do not attempt in-water installation without EZ Dock in-water coupler installation tools. DANGER Note: All empty or un-used coupler pockets should be filled with an EZ Dock pocket filler (201030); see page 38.

Show more

See Also: Doc ConverterShow details

EZ DOCK PRODUCTTools And Hardware For Installing Boat Docks

9 hours ago Hardware & Tools. EZ Dock's patented one-piece, self floating design is fast and easy to install. The simple building block design can be assembled with just a few tools. Sections come in several sizes with evenly spaced coupler pockets and multiple hardware anchor points. You choose the configuration that fits your need best and, with a simple

Show more

See Also: Doc ConverterShow details

Coupler Installation Tool EZ Dock Texas

8 hours ago Coupler installation tool. Category: Dock Accessories SKU: 9000010SS. Description. Description. This tool simplifies installation, allowing the user to assemble docks with EZ Dock

Show more

See Also: Doc ConverterShow details

EZ Dock Owners Manual EZ Dock Products

7 hours ago performing in-water installation of docks, ports and couplers can result in accidental drowning and death. Do not attempt in-water installation without EZ Dock in-water coupler installation tools. DANGER Note: All empty or un-used coupler pockets should be filled with an EZ Dock pocket filler (201030); see page 38.

Show more

See Also: Doc ConverterShow details

Accessories EZ Dock Of Maine

6 hours agoEZ Dock Coupler In-Water Installation Tool Drive Tool Socket. $61.00. EZ Dock Coupler Set. Part #301100. Drive Tool Socket In-Water Installation Tool Drive Tool Socket. $5.00. EZ Drive Tool Socket Fits on 15/16" Socket. Part #900005. In-Water Installation Tool In-Water Installation Tool In-Water Installation Tool. $89.00.

Show more

See Also: Doc ConverterShow details

Owner’s Manual And Installation Instructions For EZ Dock’s

9 hours ago the installation process (for professional installation, call your local EZ Dock dealer): EZ Dock in-water installation tool (9000010)(for EZ Dock mounting in-water assembly) Composite Coupler Installation Tool

File Size: 1MB

Page Count: 28

Show more

See Also: Doc ConverterShow details

Connecting EZ Docks YouTube

3 hours ago How do EZ Docks connect together? The patented connector system from EZ Dock - Couplers. #EZDockGTA - Talk with us at https://ezdockgta.ca/chat-with-us/

Show more

See Also: Doc ConverterShow details

Important Tips For EZ Dock Easy Installations And Maintenance

9 hours ago Use the EZ Dock coupler installation tool and a 15/16″ socket to tighten the coupler nut. Be careful not to over-tighten coupler nut. Slide coupler installation tool out through the un-coupled side of dock. You may need to tilt tool as shown to free it from bottom coupler.

Show more

See Also: Doc Converter, Ps ConverterShow details

Dock Accessories EZ Dock Gulf Coast

5 hours ago COUPLER TOOL – The patented EZ Dock coupler tool makes installation EZ. The coupler tool simplifies in-water connection of dock sections. Part #: 900010 : SECURITY CURBING – Constructed of polyethylene, EZ Dock security curbing provides a safe boarder around dock edges for wheelchairs. The dark brown color provides a matching contrast for

Estimated Reading Time: 8 mins

Show more

See Also: Doc ConverterShow details

Drive Tool 15/16" Socket Adapter For Coupler Nut FWM

2 hours ago The EZ Dock Modular Dock System is the most durable and versatile floating dock system available today. Environmentally friendly EZ Docks can remain in the water year-round and are perfect for a wide range of residential, commercial, governmental, industrial and recreational uses.

Brand: FWM Docks

Availability: In stock

Show more

See Also: Free ConverterShow details

EZ Dock Install YouTube

3 hours ago First time attempt to install EZ Dock off a 15 foot bank on the Mississippi. Easy it ain't but once in pretty slick.

Show more

See Also: Doc ConverterShow details

SeaDoo Personal Watercraft Port EZ Dock Products

4 hours ago every tool listed below for your particular installation, but the following tools are generally helpful in the installation process (for professional installation, call your local Sea-Doo or EZ Dock dealer): • EZ Dock in-water installation tool (900010)(only needed for EZ Dock mounting) • 1/2” drive ratchet

Show more

See Also: Doc ConverterShow details

Dock Installation Guides The Dock Outlet How To

4 hours ago The innovative design of our modular, floating dock sections and boat and PWC lifts makes them easy to install with a few tools and a little time. In addition, EZ Dock’s product owner’s manuals can help with any questions you might encounter.

Show more

See Also: Doc ConverterShow details

COUPLER INSTALLATION TOOL Diamond Waterfronts

7 hours ago This tool simplifies installation, allowing the user to assemble docks with EZ Dock couplers without getting in the water. Learn more about this product by visiting the manufacturers website: www.ez-dock

Show more

See Also: Free ConverterShow details

Dock Installation Guides Gateway EZ Dock How To

4 hours ago The innovative design of our modular, floating dock sections and boat and PWC lifts makes them easy to install with a few tools and a little time. In addition, EZ Dock’s product owner’s manuals can help with any questions you might encounter.

Show more

See Also: Doc ConverterShow details

FAQ EzDock West

8 hours ago An in-water coupler installation tool and a coupler nut tool are the only special tools required to assemble the EZ Dock sections. A hammer, ratchet, 15/16” wrench or socket, and a Phillips head screwdriver are also needed. What is inside the EZ Dock sections. The EZ Dock one-piece sections contain no fillers or foam for floatation.

Estimated Reading Time: 6 mins

Show more

See Also: Doc ConverterShow details

Repair A Leaking EZ Dock Fixing A Cracked Or Punctured

2 hours ago The EZ Dock system includes couplers which are designed to break before a dock section cracks which is the reason the docks are provided with an 8 year warranty. EZ Dock is the most durable dock system available today and issues regarding cracks from storm damage are extremely rare.

Show more

See Also: Doc ConverterShow details

DRIVE TOOL 15/16″ SOCKET ADAPTOR Diamond Waterfronts

3 hours ago 330.882.5296. (You save ) (No reviews yet) Write a Review. Write a Review. ×. EZ Dock. DRIVE TOOL 15/16″ SOCKET ADAPTOR. Rating Required Select Rating 1 star (worst) 2 stars 3 stars (average) 4 stars 5 stars (best) Name.

Show more

See Also: Free ConverterShow details

EZ Dock Dealer Brigantine & Atlantic City, NJ

9 hours agoEZ Dock Dealer and Installer. Stop by and check out the variety of “EZ Dock” floating docks, boat docks, PWC lifts and accessories we have available. Contact us today so we can design and install a personal floating dock that fits your exact needs. EZ Dock floating docks are the best investment you can make in your waterfront property.

Show more

See Also: Doc ConverterShow details

Ezdocktexas.com Floating Docks News & Tips

4 hours ago Use the EZ Dock coupler installation tool and a 15/16″ socket to tighten the coupler nut. Be careful not to over-tighten coupler nut. Slide coupler installation tool out through the un-coupled side of dock. You may need to tilt tool as shown to free it from bottom coupler.

Show more

See Also: Doc Converter, Ps ConverterShow details

Can I Install My Dock Myself? EZ Dock Of MidAmerica

Just Now The hardest part of the EZ Dock installation process is generally just getting your EZ Dock product into the water. This is where having an extra hand is required. Once you start getting pieces in, simply connect them with EZ Dock’s coupler system, which is hooked into the pockets of the dock

Show more

See Also: Doc ConverterShow details

9000010SS – Shoco Marine

6 hours agoEZ Dock Railing; Aluminum & Poly Gangways; Stationary Docks & Boat Lifts. Shorestation Boat Lifts; Shorestation PWC Lifts; Shorescreen Power Curtains Contact Us; Blog; 9000010SS. Home → Products → 9000010SS. 9000010SS. In-Water Coupler Installation tool – Stainless Steel. SKU: 9000010SS Category: EZ Dock Accessories. Related products

Show more

See Also: Free ConverterShow details

EZ Port & Stow Personal Watercraft Port

4 hours ago every tool listed below for your particular installation, but the following tools are generally helpful in the installation process (for professional installation, call your local EZ Dock distributor or dealer): EZ Dock in-water installation tool (900010)(only needed for EZ Dock mounting) 1/2” drive ratchet

Show more

See Also: Free ConverterShow details

Drive Tool 15/16″ Socket Adaptor EZ Dock Texas

4 hours ago Drive tool 15/16″ socket adaptor. Drive tool 15/16″ socket adaptor. Category: Dock Accessories SKU: 900005. Description. Description. The adapter fits on a standard 3/4″ socket and drive to tighten the coupler nut, which allows the dock to move and flex in rough water without loosening.

Show more

See Also: Doc ConverterShow details

EZ Dock Installation Tool For Dock Piece Connectors Boat

8 hours agoEZ Dock installation tool for dock piece connectors - $75 (Wausau) < image 1 of 2 > condition: like new. QR Code Link to This Post. This tool is unbelievably handy at getting the black EZ Dock "dog bone" connectors installed. Unless you are a scuba diver, putting the bottom (under dock) half of these connectors in can be really tough. This

Show more

See Also: Doc ConverterShow details

Amazon.com: Ezdock

2 hours ago ICY DOCK Dual Tool-Less Dual 2.5 to 3.5 HDD Drive Bay SSD Mounting Bracket Kit Adapter - EZ-Fit Lite MB290SP-B (Two Units) 4.6 out of 5 stars. 1,355. $12.49. $12. . 49. Get it as soon as Thu, Sep 23. FREE Shipping on orders over $25 shipped by Amazon.

Show more

See Also: Doc ConverterShow details

Cart FWM Docks & EZ Dock Northeast

6 hours ago Plastic EZ Docks. The EZ Dock Modular Dock System is the most durable and versatile floating dock system available today. Environmentally friendly EZ Docks can remain in the water year-round and are perfect for a wide range of residential, commercial, governmental, industrial and recreational uses. Learn More. Floating. Jet Ski Lifts. Boat Lifts.

Show more

See Also: Doc ConverterShow details

SATA Hard Drive To USB (Docking Station) Wholesale

1 hours agoEZ-DOCK. Kingwin introduces the new EZ-Dock (Model EZD-2535U3) Super-Speed USB 3.0 to SATA Hard Drive Docking Station which boasts a 10 x faster USB speed. The EZ-Dock allows easy insertion and hot-swap of any 2.5” or 3.5” SATA HDD or SSD. It is …

Show more

See Also: Doc ConverterShow details

EZDock Your Source For Floating Docks And Accecoreries

4 hours agoEZ-DOCK TAMPA. Address. 1600 E. Busch Bvd Tampa Bay FL 33612. Second Location. 10321 N. Dale Mabry Hwy Tampa, FL 33618. Call us (813)917-0331

Show more

See Also: Doc ConverterShow details

EZ Dock EZ Kayak Launch YouTube

3 hours ago About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators

Show more

See Also: Doc ConverterShow details

EZ Dock Pole Removal YouTube

3 hours ago Here is how we pull the poles in order to put our marina away for the winter. We do things by hand on smaller jobs but you can't beat the crane for the bigg

Show more

See Also: Doc Converter, Mov ConverterShow details

Dock Accessories EZ Dock Texas

Just NowEZ Dock offers a variety of floating dock accessories to help you make your waterfront more accessible, more fun and more practical. You can use our products with your existing dock or with an EZ Dock system. All our products are designed with the same durability, safety and quality as our floating docks.

Estimated Reading Time: 2 mins

Show more

See Also: Doc ConverterShow details

Kawartha EZ Dock – The Best Docks On The Market

1 hours agoEZ Dock Floating Docks Make Boating Better. Kawartha EZ Dock changes the way you look at docking, with installation, removal and service options to ensure you have the best experience with your dock! Maintenance Free! Can be lest in the water in some locations; Does not wear, change colour, or even need maintenance!

Show more

See Also: Doc ConverterShow details

Filter Type:All TimePast 24 HoursPast WeekPast month

Please leave your comments here:

Frequently Asked Questions

What's the best way to install an EZ dock?

Insert Coupler Bolt through bottom coupler section (square recess) and use hammer to set bolt into recess of bottom coupler. Load bottom of coupler & bolt assembly into coupler installation tool.

What is the EZ dock in water coupler tool?

In-Water Installation Tool The patented EZ Dock In Water Coupler Tool makes installation easy. The tool simplifies in-water connection of boat lift parts and dock sections. Supplemental Flotation for Docks

What are the advantages of an EZ floating dock?

Some of the chief advantages of the EZ Dock system include: Rubber couplers are used to connect dock sections to one another. Use an In-Water Installation tool to pull the coupler up from in the water, connect the top rubber coupler and tighten with a composite nut.

Who are the creators of the EZ dock?

EZ Dock was created by two water enthusiasts who were tired of the heavy maintenance, frequent storm repairs and the carbon footprint associated with traditional dock options.

Sours: https://convertf.com/ez-dock-installation-tool/
  1. Chase associate program mba salary
  2. 1995 ford f150 factory radio
  3. Boost mobile coolpad surf reviews
  4. Mini cooper s 2014 interior

Tips

How to adjust the free board

picture of docks with adjusted free board

EZ Dock is delivered with a 13.5″ free board (the distance between the top surface of the dock and the water).

Some dock applications are better served with less free board, such as docks used by rowing teams. It is easy to adjust the free board and we simply put a removable “plug” in each dock in the coupler pocket and pump water into the dock until it provides the desired free board.

Using a plug with threads the water can be removed by simply reversing the process. This installation uses a 5″ free board which provides rowing teams easy access on and off boats.

Tightening and removing couplers

Tightening couplers

picture of EZ Dock socket adapter for coupler nut

If you are in rough water locations take a few minutes in the Spring and make sure all of your coupler nuts are tight.

EZ Dock is designed to move “with” rough water much like a catepillar moves across a surface. If you want to see the advantage in using EZ Dock visit our gallery of videos and watch EZ Dock in a hurricane.

The couplers allow the dock to move and flex in rough water which could loosen nuts that hold the top and bottom connector together. Simply snug them up and you are good for another season. To tighten a coupler nut you need the socket adapter that fits on a standard 3/4″ socket and drive – do not over tighten as you can break the poly bolt, just snug it up.

The socket adapater is part number 900005 and has a cost of $1. The official name of the part is DRIVE TOOL SOCKET FOR COMPOSITE PRODUCT.

Removing Couplers

picture of EZ Dock Coupler Tool

If you are removing couplers for any reason remove the nut on the top coupler, tie a string around the threads of the bolt that the nut was covering and rock the dock by standing over the connection point. The bottom coupler will drop out and you can retrieve the bottom coupler and bolt easily for re-use.

Docking your PWC

The key to docking a personal water craft [PWC] on an EZ Port 3 is control of the Waverunner.

Any PWC with reverse makes it easier to bring the nose of the Waverunner to touch the first roller in the water. Once you have come to a stop with the nose of the Waverunner against the roller then accelerate and “climb” the machine onto the dock. Hitting the first roller or either side of the dock near the roller while moving can damage the hull of the Waverunner.

The recommended process for docking the machine is to use reverse if you have it on your PWC and stop forward motion – when the roller and hull are aligned, then give the Waverunner throttle to roll over the first roller and next three. If you do not have reverse approach the EZ Port 3 as slowly as possible but stay centered on the roller.

How to avoid losing couplers

picture of EZ Dock socket adapter for coupler nut
coupler socket adapter

Uncoupling the EZ Dock Sections is simple

To uncouple EZ Dock section your will need a socket adapter tool which fits on a standard 3/4” socket drive. The tool is an adapter that will fit the coupler nut that holds the top and bottom coupler together between the dock sections. The socket adapter has a star shapped pattern that is designed to fit into the same pattern on the coupler nut.

The black couplers (some people call the dog bones due to their similar shape) consist of a top coupler, bottom bottom coupler and a black plastic poly bolt and nut. The only “trick” to taking the dock sections apart is not to lose the bottom coupler which can fall out if you do not use a string on the coupler bolt for retrieval (see note below regarding string).

Simply back off the plastic nut and remove the top coupler with a flat screw driver prying it out of the dock pocket. This will expose the black poly bolt that is left – do this for each coupler in the line that is holding the one dock section together. Only disconnect one dock at a time.

  • There are six couplers if docks are joined side to side
  • There are four couplers between the 80″ X 10′ dock sections
  • There are three couplers between a 60″ X 10′ dock sections
  • There are two couplers between the 40″ X 10′ dock sections

Remove only one row of coupler nuts at a time (one dock section at a time).

Once you have the nut and top black coupler removed tie a string using a “slip knot” around the threads of each coupler bolt that is exposed and replace the coupler nut over the string. Stradling the two dock sections that are joined rock the docks and the coupler bottom and bolt will fall out. Keeping the string in your hand pull the string between the docks and bring the couplers to the top of the dock (otherwise the bottom coupler and bolt will fall to the bottom – they do not float).

Pipe Brackets

Pipe brackets can be removed in a similar manner – the Heavy Duty pipe brackets use couplers, the Light Duty pipe brackets use screws to join the upper and lower pieces.

Piling Brackets

Piling brackets can be disconnected easily.

Hinge Kits

Hinges kits simply have a cotter pin and straight pin that is removed to separate an EZ Dock that was connected to a wood dock.

Dock Cleats

Cleats on a dock make it easy to secure the dock section after it is disconnected from the system and the cleats are strong enough to allow a dock section to be lifted by dock lines on the cleats if you have a way to hoist the dock section.

Otherwise just pull the dock section on to what dock is left and then carry it from the water via the gangway or beach path.

Increasing the Efficiency of your EZ Port 2, 3 and 4

We hear from customers that it is difficult to launch their watercraft and they have to strain and lift the machine with one or more people pushing.

There are two things you can do to eliminate this problem and make launching and docking easy for any owners:

1. Grease the rollers each year – this requires a special tip that will fit on any grease gun and you can use the Lincoln Grease Needle LNC-5803 (see photo below). This part is available from The Tool Warehouse and many other online tool stores on the web (google the phrase above). The cost with shipping is approximately $14.25.

grease needle

Lincoln Grease Needle LNC-5803

port-3

2. Adjust the rollers – the watercraft should be resting on the rollers, not the dock. If they are adjusted properly the machine will rock slightly from side to side when on the dock which keeps the watercraft off the dock while launching or docking. There are several roller adjustments you can make that either raise or lower the rollers with the third roller (on the Port 3) the most critical.

Please see this document for additional details.

How to position Port Max rollers

picture of Position of the EZ Port Max Roller

When installing the skate wheel roller and spacer for difficult to move machines make sure the roller is placed in this position on each side of the Port Max.

This will provide the best platform on which to roll the machine, especially the more difficult hull of some of the Yamaha PWCs.

Every PWC should roll easily on and off the dock using this wheel position.

How to install the EZ Dock hinge kit

picture of hinge kit for EZ port installation

A hinge kit comes with two connection points – each hinge has a hinge plate and a J Bracket. The J Bracket attaches to the EZ Port by inserting the J Bracket in the top pocket with the hardware connector in the bottom pocket. This secures the part of the hinge that is mounted on the EZ Port.

The other half of the hinge is a flat bracket that has holes for lag bolts. The two pieces (J Bracket and Hinge Plate) are joined using a hinge pin which slides through the two pieces and is secured with a cotter pin.

Once installed It is easy to remove the Port from the floating dock – you simply pull the cotter pin out and slide the pin out – and your EZ Port is disconnected.

The “key” to a successful installation is marking the location for the lag bolts.

  1. mount the J Bracket and secure it to the EZ Port
  2. slide the hinge pin through the J Bracket and the hinge plate and secure it with a cotter pin
  3. while standing/kneeling on the EZ Port hold the hinge plate against the existing floating dock and mark where the lag bolts will be located.

KEY – you must have your weight on the EZ Port and no one on the dock you are attaching to when you mark the position for the lag bolts. This negative load will then insure that when your PWC is on the EZ Port the back end will rise and keep the jet drive completely out of the water. The negative load on the installation when marking the spot for the lag bolts is critical.

Note: Depending on the free board of your existing floating dock the hinge plate can be mounted in the up (raised position above the J bracket) or at the same height as the J Bracket.

One hinge kit is adequate for securing up to three EZ Ports depending on the degree of rough water at the site.

Ice doesn't affect EZ Docks in the winter

You can leave your EZ Docks in during the winter

Ice has no affect on the EZ Dock System. Since an EZ Dock requires only an inch of water to float, the docks will “pop” to the top of the ice when the water freezes, much like an ice cube tray.

The YMCA of Greater NY selected EZ Dock for a number of reasons, one of which was the historical issue of removing docks in the Fall and then installing them again in the Spring. Not only was this a significant effort and expense requiring a large number of staff members dedicated to this activity, the removal of the docks actually caused damage which had to be repaired each year.

YMCA installation - EZ Dock on a frozen lake

This picture was taken at the camp after a 20” ice condition for most of the winter which had no affect on the EZ Dock System. The only time you should have concern with ice conditions is when there is a significant ice flow since this often takes pilings and other anchoring systems with the ice flow as well as the dock system.

But should you want to remove your docks…

picture of wheels used to move dock sections

If you want to remove the docks for winter storage it is easily accomplished using the EZ Dock Dock Wheels (Part# 90050 – pictured below) which attach to the docks and allow you to “tow” the docks while connected from the water to land. Another method of removing the docks is to place PVC pipe on land and use the pipe as the roller system when towing the docks from the water.

How to measure for a FloatStep®ladder

The industry’s first dock ladder to remove itself automatically when not in use is now available for fixed and floating docks (watch short video).

Gone are the barnacles and the marine growth that have been a part of every ladder prior to the introduction of the FloatStep® ladder.

Flip up ladders, pull up ladders and all other variations of dock ladders fail when someone forgets to remove the ladder after each use. Fixed ladder steps remaining in the water are a constant problem to customers causing injury and aggravation.  Even if you have a removable ladder the increased danger of being in the water unexpectedly and not being able to access the ladder is a greater risk.

How to measure for a FloatStep Ladder

measure ladder

  1. Measure from the top of your dock to the lowest water mark.
  2. Add a minimum of one (1) foot to measurement.
  3. The resultant number tells you how many steps your ladder should have – see Example below.

Example:

  • The top of your dock to the lowest water mark measures 3 ft.
  • Add 1 ft. to your measurement
  • You will need a 4 Step ladder

Note that adding the additional 1 foot length to the measurement will allow for safe and constant ladder availability.

Maintaining your EZ Docks

To keep your EZ Docks looking like new simply use a power washer to remove dirt and grime. A good high pressure power washer should clean your docks without any soap or cleaner most of the time.

Multiple Dock Levels

picture of docks with adjusted free board

If you need a floating dock with different heights EZ Dock can be stacked two, three or four levels high.

This is a common application when different levels are required for boarding different boats that have different heights. One section of the dock could have a 13″ free board, another 26″, another 39″.

Your EZ Dock Dealer can assist you in the hardware required to accomplish this type of installation. Often times commercial transport applications required different levels of dock for loading.

How to Repair a Leaking Dock

Many times a cracked or punctured EZ Dock section can be repaired by simply melting the polyethylene dock material with a torch or plastic welding iron (a large hot metal iron that melts the plastic together). Occasionally we have customers that have punctured or cut the dock with bullets, boat propeller from an outboard engine or some other accident and we use an old dock section to piece a repair and melt that into the open hole. If you have stress cracks near coupler pockets they normally occur after constant large storms due to extreme pressure on the dock. At times these cracks can be repaired in the same manner, melting the material together, but if it is in place that receives a lot of stress it may not hold.

The EZ Dock system includes couplers which are designed to break before a dock section cracks which is the reason the docks are provided with an 8 year warranty. EZ Dock is the most durable dock system available today and issues regarding cracks from storm damage are extremely rare.

You also have a “weep hole” on the end of each dock section that allows the dock to change pressure inside as atmospheric conditions change outside. At times in rough water we have seen water enter the docks through the weep hole but this is normally in salt water applications where waves are bouncing off a bulkhead and back into the dock system. This year EZ Dock introduced a new vent (see attachment) which can be used that will prevent any water from entering the dock regardless of rough water conditions. These can be inserted into a hole in the end of the dock while you seal the original “vent hole” that has been included since the docks were invented 20 years ago. You can plug the old vent hole with any silicone material similar to bathtub caulk.

Draining docks is a simple process – drill a hole in one corner on the edge of the dock near the top, drain the water, and purchase a threaded plastic plug from Home Depot of the same size you make the hole, the plug will prevent water from entering the dock through the drain hole you created. Since the entire dock section is an open chamber only one hole is required to drain the entire dock.

Sours: https://ezdockinnovations.net/resources/tips/
Refurbished EZ Port 2 Installation

The Patented Coupler System is the Key Building Block of EZ Dock

The rubber coupler set is the functional cornerstone of the EZ Dock System

Every dock section, EZ port, anchoring option or accessory, utilizes this brilliantly simple 3-piece coupling system to connect, protect, and provide unmatched stability in the water. Featuring two couplers and a nylon-composite rod and nut – the coupler connection system effectively keeps thousands of pounds of EZ Docks connected and protected against the destructive nature of water current, chop, and fluctuating levels.

The Coupler System is Simple, Strong, Resilient, and Flexible

Simple – A 3-piece system that connects all EZ Dock products together

Strong – Can absorb up to 4,400 pounds of torsion (twisting pressure)

Resilient – The degenerative elements of weather cannot break them down

Flexible – No matter the directional torquing movement of the water, couplers flex to protect the docks

EZ Dock Coupler Set

The Tensile Strength of the Coupler system is the key to the Long Lifespan of an EZ Dock System

Any waterfront owner knows just how susceptible docks can be to the constant bombardment of the destructive and unpredictable behaviour of water movement. The swirling currents of water can wreak havoc on fixed or floating docks over time. It is this susceptibility to breaking down that the engineers at EZ Dock focused on when designing the functional abilities of the coupler system.

The movement of a body of water is not linear, it moves based on weather conditions, bed slope, bed shape, obstructions and human elements. All of these environmental factors act upon and influence the constant movement of a body of water. Regardless of the way our eyes interpret it, water is not moving in one direction. Water movement is at the mercy of everything from terrestrial factors to gravity, and even the effects of the moon.

What does this have to do with your floating dock system?

Simple, the omnidirectional motion of water constantly exacts torsional pressure (of different levels) on docks. It’s this unrelenting twisting pressure that can ultimately break down a dock system over time.

EZ Docks are engineered with a protective element in its design – the coupler. The coupler is not solely the connective linchpin of EZ Docks, it’s the key component to their longevity. Each coupler is constructed to absorb and effectively disperse the torsion of water movement, up to 4,000 lbs of twisting pressure per coupler! It’s this combination of absorptive and dispersive functionality that protects your EZ Dock against virtually any torsional stress. Just think, if you have an EZ Dock system featuring 4 x 80” sections connected end to end – it’s utilizing 12 coupler sets – which is 24 individual couplers. If each coupler can withstand up to 4,000+ lbs of pressure; that means this setup would boast in excess of 96,000 lbs of protection against the adverse effects water torsion. This is how EZ Dock created the world’s strongest floating dock system.

Here’s How Couplers Connect Your EZ Dock System

Each rubber coupler features a top and bottom, the bottom is identified by a slightly tapered design to fit snugly in the dock pockets on both the top and underside of the dock.

EZ Dock Couplers Protect Docsk

When connecting two EZ Dock sections, a nylon rod is inserted into one coupler and secured with a hammer. The coupler with the rod is then seated in the custom in-water installation tool which is submerged in the water and slid between the dock sections being connected. Once the pocket is reached, the coupler is pulled up into the pocket from under the dock. As the coupler is pulled into the bottom pockets the rod reaches the top coupler where the nut is inserted and screwed to securely pull the coupler set together, completing the coupling. EZ Dock sections have pockets spaced every 20” around its perimeter, top, and bottom. These pockets seat the tapered couplers above and beneath the water to connect dock sections in virtually any configuration.

EZ Dock Connection Pockets

The Strength, Flexibility, and Resiliency of the patented Coupler system is what makes everything EZ Docks can do – Possible

Sours: https://ezdockgta.ca/how-ez-docks-work/connections/

Coupler ez installation tool dock

Accessories

Dock AccessoriesEZ Dock Swim PlatformHEXAGON DOCKS – EZ Dock adds even more layout versatility with our new half-hexagon dock option.EZ Dock Swim PlatformMANY CONFIGURATIONS – Want to create your own paradise? Peace of mind as well as peace and quiet can all be achieved yours when you choose EZ Dock for your waterfront design needs. EZ Dock sections allow you to create dock platforms that can be enjoyed a multitude of ways.EZ Dock GangwayGANGWAY – VERSATILE DURABLE & SAFE – EZ Dock’s new polyethylene gangway offers the same durability, stability, and modular versatility of our docks. It last longer than wood and its cool, beige, slip-resistant surface is more comfortable to the touch. Available in 6’ (1.82m) sections, which can be combined to lengths of 12’ (3.65m) and 18’ (5.48m) depending upon your water condition, EZ Dock provides you access to fun. Railings are also available for added safety. Many of our gangway models can also be used for existing wood docks.EZ Dock Access RampWETLANDS INSTALLATIONS – EZ Dock knows that people like to explore natural habitats. EZ Dock has many configurations that can be used to access areas such as wetlands, etc. EZ Dock provides a safe, eco-friendly environment for people to do just that–explore without disturbing the natural surroundings.EZ Dock Fishing PierFISHING PIERS – Did you let the big one get away because you were afraid of falling off the dock? EZ Dock offers complete fishing pier configurations that include railing designed specifically for fishermen. This special railing offers unique fishing pole holders that come in handy while you grab your tackle or a net.  Plus, choose from a wide variety of railing colors to match your home, villa, camp, or cabin décor.EZ Dock Boat LaunchBOAT LAUNCHING – With more and more areas become public access, the need for durable, safe, products are becoming a must. EZ Dock makes launching boats EZ and safe. You can offer tie off cleats and bumpers for added safety. Plus, you get the stability of the EZ Dock system, which is steadier than traditional floating dock sections. The EZ Dock patented lock coupler system also provides a barrier against vandals and thieves.EZ Dock BumperDOCK BUMPER – The new dock bumper comes complete, ready to install onto any dock.
Part #: 300180EZ Dock Storage BoxSTORAGE BOX – EZ Dock storage box is permanently mounted and constructed of weather-resistant materials. The storage box is a great place to store life jackets, towels, and any other essential supplies.
Part #: 300750EZ Dock Corner Storage BoxCORNER STORAGE – Our corner storage box has roomy storage in a compact design that makes the most of available space without interfering with foot traffic. Connection boxes for complete utility hookups through this box are also available.
Part #: 300755EZ Dock SlideEZ DOCK SLIDE
The popular dock slide utilizes rugged, durable, polyvinyl-coated steps, and a one-piece polyethylene bed-way, for a smooth ride. Install with almost any EZ Dock where water depth is more than 5’ (1.5m).
Part #: 300600EZ Dock Tie-Down CleatsTIE DOWN CLEAT – EZ Dock tie down cleats attach to heavy-duty stainless steel T-nuts molded in pairs around dock section perimeters. Cleats are 8” (20.32cm) long.
Part #:300100EZ Dock Hardware Kit for BenchPOLYETHYLENE DOCK BENCH – Relax and take a seat in EZ Dock’s polyethylene dock bench. EZ to clean and with the arm option, it comes complete with cup holders for your cool-refreshing drink. Hardware is included with both options to attach to any EZ Dock system.
Part #: 300970
Part #: 300965 without arm restEZ Dock Boat Launch StrapBOAT LAUNCH STRAP – EZ Dock boat launch strap attaches through a pulley to winch, reversing direction of pull to launch a boat with the same winch used for docking.
Part #: 900070EZ Dock Supplemental FlotationSUPPLEMENTAL FLOTATION – Need an extra boost? Supplemental floatation attaches under dock sections and EZ Port lifts to increase floatation capacity where certain applications may need to support extra weight.
Part #: 206013EZ Dock EdgingPROTECTIVE CUSHION – Constructed of durable vinyl, EZ Dock edging provides a soft cushion to protect water vessels from the sides of docks and vise versa. This product can also be used with regular existing docks to a updated look.
Part #: 400116EZ Dock WheelsMOVING WHEELS – Need to move a dock section? With EZ Dock dock wheels, you can do just that. Constructed of steel frames and polyethylene wheels that make movement of docks easier. Perfect for docks at camps and colder climates where dock sections are taken out on an annuals basis. Sold in pairs.
Part #: 900050EZ Dock Coupler Installation ToolCOUPLER TOOL – The patented EZ Dock coupler tool makes installation EZ. The coupler tool simplifies in-water connection of dock sections.
Part #: 900010Dock Security CurbingSECURITY CURBING – Constructed of polyethylene, EZ Dock security curbing provides a safe boarder around dock edges for wheelchairs. The dark brown color provides a matching contrast for easy visibility for your dock.
Part #: 35116EZ Dock Utility ChannelUTILITIES CONDUIT – Need to channel electricity or water to and from your dock? Our utility channel allows just that. The two-piece chase-way attaches to the side of the EZ Dock sections, allowing conduit for utilities. Available in 60” (152.4cm) or 20” (50.8cm) length sections and stainless-steel hardware options to match your specific needs. Each section is 20” (50.8cm) wide. 1
Part #: 302060 (60”x20”), Part #: 303260SS (60”x20” stainless steel),
Part #: 302020 (20”x20”), Part #: 302020SS (20”x20” stainless steel)EZ Dock Utility Channel Inside CornerCONDUIT INSIDE CORNER
EZ Dock Utility Channel Inside Corner
Utility conduit can be tucked neatly inside two-piece chaseway attached at junction of dock sections. Available with stainless-steel hardware.
Part #: 302030, 302030SSEZ Dock Utility Channel Outside CornerCONDUIT CORNER – The corner utility channels allows for convenient installation where dock layouts require conduit to be installed around the outside corner of a dock section. Available with stainless-steel hardware for your specific application needs. 
Part #: 302040
Part #: 302040SS (stainless steel)EZ Dock Corner GussetCORNER GUSSET – Add a shortcut to your dock! Corner gussets offer added deck surface and stability to dock fingers when needed.
Part #: 300501EZ Dock Transition Kit (Polyethylene)TRANSITION KIT – Want to add an EZ Dock to an existing floating dock for added room? You can, with a transition kit made from EZ Dock. This hinged polyethylene plate creates a smooth transition between EZ Dock and another existing floating dock or PWC lift.
Part #: 100717 (15” / 38.1cm)
Part #: 100718 (30” / 76.2cm)power water stand or stationPOCKET FILLER – EZ Dock is pleased to announce the availability of the “pocket fillers” for those customers that wish to cover the unused pockets on an EZ Dock installation. If you prefer to have a solid dock along the edges the pocket filler can be inserted easily and it will hold in place based on the design of “tabs” on either side of the pocket filler. It can be removed by simply using a screwdriver to pry an edge up and used again by replacing the two tabs held by a screw. The pocket fillers are a similar color as the EZ Dock system.picture of glow in the dark pocket fillerGLOW IN THE DARK
POCKET FILLER
– Introducing EZ Dock newest pocket filler that “Glows-in-the-Dark” green. These new pocket fillers are the same as the standard EZ Dock pocket filler but have a strong glow in the dark that will stay glowing till dawn. With a charge time of 15 minutes and a half glow life of 2.5 hours they will provide visibility to any EZ Dock installation.picture of hydrophobic ventHYDROPHOBIC VENT – All future production of docks and ports will include one of these vents to replace the “open to atmosphere” vent. This new vent is designed to allow the dock/port sections to breath but will not allow water in pass through. The new vent will be factory installed in one of the spin weld areas. In addition these vents can be purchased to retro fit older dock sections in the field using only a drill. A Drill and Tap Kit is also available (9000029) and comes with a 7/16” drill bit and a 1/4” NPT tap (this TAP threads the 1/2” hole into which the vent is threaded).
Sours: http://www.aplusezdock.com/products/ez-dock-products/accessories/
Refurbished EZ Port 2 Installation

Accessories

EZ Dock Coupler

In-Water Installation Tool

Drive Tool Socket

EZ Dock Coupler / "Dog Bone"

$61.00

EZ Dock Coupler Set

Part #301100

Drive Tool Socket

In-Water Installation Tool

Drive Tool Socket

EZ Dock Floating Dock Drive Tool Socket

$5.00

EZ Drive Tool Socket Fits on 15/16" Socket

Part #900005

In-Water Installation Tool

In-Water Installation Tool

In-Water Installation Tool

In-water Install Tool for EZ Dock floating docks

$89.00

Install Tool

Part #90000010SS

Dock Bumper

Standard Duty Pipe Bracket

In-Water Installation Tool

Dock Bumper for EZ Dock floating docks

$99.00

EZ Dock Bumper

Part #300180

Standard Duty Pipe Bracket

Standard Duty Pipe Bracket

Standard Duty Pipe Bracket

Standard Duty Pipe Bracket  for EZ Dock floating docks

$170.00

One Piece Poly Pipe Bracket

Part #135350

Heavy-Duty Pipe Bracket

Standard Duty Pipe Bracket

Standard Duty Pipe Bracket

Heavy Duty Pipe Bracket for EZ Dock floating docks

$265.00

Heavy-Duty Pipe Bracket

Part #215-350

Sours: https://ezdock-maine.com/accessories

Similar news:

Into a fluffy girl, into a girl providing services of an intimate nature to men for money. And she liked to feel that way. As soon as the front door closed behind them, he grabbed her in his arms and carried her into the room. There Max threw Lolita on the bed, took off his shirt.



1051 1052 1053 1054 1055