Mks sgen l v1 0

Mks sgen l v1 0 DEFAULT

Mks sgen l firmware upload difficulties

this is my second time uploading firmware so my experience may not up to par with you fine people.

Just finished building the lowrider and noticed the uno with v3 sheild just wont do it. since we are in lockdown i ordered a makerbase mks sgen l v board because of the cost and quick shipping.

prior i had the ide with anet configurations in the library folder of marlin and opted out to just delete everything and reinstall the newer (tried with ) arduino.

i open the ramps mpcnc marlin folder with only opens the marlin/configuration.h/config_adv.h/and bootscreen and thats all. was i suppose to copy those over to a marlin folder? (i have the drv steppers so the 32 step configuration is correct yes?)

i put the proper board name in config and have monitor library installed.
ch4iser driver installed. as had it prior for the anet board.

i might of used a different UART? earlier and when i had windows recognize the chip as “smoothie serial number” then reinstalled the ch41ser and its back to the pop up “unrecognizable” .

the port " com 10" pops up and off when i unplug it.

so far ive gone through and identified these to get to where i am now which is


Arduino: (Windows 10), Board: “Arduino Mega or Mega , ATmega (Mega )”

Build options changed, rebuilding all
Sketch uses bytes (43%) of program storage space. Maximum is bytes.
Global variables use bytes (56%) of dynamic memory, leaving bytes for local variables. Maximum is bytes.
C:\Users\AppData\Local\Arduino15\packages\arduino\tools\avrdude\arduino17/bin/avrdude -CC:\Users\AppData\Local\Arduino15\packages\arduino\tools\avrdude\arduino17/etc/avrdude.conf -v -patmega -cwiring -PCOM10 -b -D -Uflash:w:C:\Users\nolan\AppData\Local\Temp\arduino_build_/Marlin.ino.hex:i

avrdude: Version
Copyright © Brian Dean,
Copyright © Joerg Wunsch

avrdude: stkv2_ReceiveMessage(): timeout
avrdude: stkv2_ReceiveMessage(): timeout
avrdude: stkv2_ReceiveMessage(): timeout
avrdude: stkv2_ReceiveMessage(): timeout
avrdude: stkv2_ReceiveMessage(): timeout
avrdude: stkv2_ReceiveMessage(): timeout
avrdude: stkv2_getsync(): timeout communicating with programmer

avrdude done. Thank you.

An error occurred while uploading the sketch

This report would have more information with
“Show verbose output during compilation”
option enabled in File -> Preferences.

not sure what im missing with this avrdude situation. i tried finding and installing a avrdude from zip source but not sure if. please let me know im on day 3 and exhausting efforts, anything would be so greatly appreciated.

Sours: https://forum.v1engineering.com/t/mks-sgen-l-firmware-upload-difficulties/

MKS SGEN V &#; Control Board 3D Printer &#; CNC

MKS SGEN V &#; Control Board 3D Printer & CNC

MKS SGEN V, is a controller board % compatible with the Smoothieboard.

It has 5 sockets, in which the stepper drivers can be inserted: ,, TMC, TMC, etc.

It is suitable for the control of 3D printers and CNC machines.

For CNC machines it allows the connection of external stepper motor drivers hat uses high-current motors..

Main features of the MKS SGEN V

  1. Use 32 bit Cortex-M3 LPC main chip, with MHZ main frequency
  2. Is a significant improvement over the 8 or 16bit plates
  3. It uses Smoothieware&#;s highly modular open source firmware, easy for secondary development.
  4. It has 5 sockets, in which the stepper drivers can be inserted: ,, TMC, TMC and so on.
  5. Support external big stepper drivers to fit the printers that uses high-current motors.
  6. .Support network function, then proceed remote control via IE Explorer
  7. The stepper motor currents can be configured directly, which can prevent damage.
  8. Use of 4-layer FR-4 PCB of high quality and special design for cooling.
  9. Use a professional power chip, support 12VV DC.power input.
  10. Work with MKS TFT series touch screen and LCD
  11. It is recommended to use the MKS TFT28, TFT32, etc.  touch screen.

Wiring:

 

Only logged in customers who have purchased this product may leave a review.

Sours: https://makershopbcn.com/product/mks-sgen-ven
  1. 1996 chevy tahoe led headlights
  2. Take ten tire tulsa ok
  3. 1995 toyota tacoma interior parts

The pin names of the MKS SGen L v in the firmware

MKS SGen L v Pinout Diagram

MKS SGen L v

MKS SGen L v Driver Pins in Firmware

Driver pin numbers. They are separated into driver number.

Pin Type01234
Enable Pins
Step Pins
Direction Pins
UART Pins

MKS SGen L v Other Pins in Firmware

If more than one pin name is availble, either name can be used in the firmware (config.g). If the pins aren’t in the table (due to not having a special name), then the pin itself can be used in the form of P or P0_1.

Pin NumberPin Name 1Pin Name 2
e0tempth1
bedtempTB
e1tempth2
led4
led3
led2
led1
servo0
zstopmaxZ+
zstopZ-
ystopmaxY+
ystopY-
xstopmaxX+
xstopX-
servo1
fan0fan
bed
e1heathe1
e0heathe0

Tags:


Sours: https://teamgloomy.github.io/mks_sgen_l_1_pins.html
MKS SGen L 32bits, TFT35, TMC2208 UART y LCD12864

MKS SGen L V

I can't seem to get my motors to move.

I am using the mks tmc v1 that came with the sgen L.

I removed the diag jumpers that were installed for sensorless homing since I read that the mks v1 doesn't support it.

When I try to home any axis no motors move and the board halts with a "homing failed" message.

Any ideas? Here is the output from M

: X Y Z Z2 E
: Address 0 0 0 0 0
: Enabled false false false false false
: Set current
: RMS current
: MAX current
: Run current 25/31 25/31 25/31 25/31 25/31
: Hold current 17/31 17/31 17/31 17/31 17/31
: CS actual 17/31 17/31 17/31 17/31 17/31
: PWM scale 20 20 20 20 20
: vsense 1= 1= 1= 1= 1=
: stealthChop true true true true true
: msteps 16 16 16 16 16
: tstep max max max max max
: pwm
: threshold 79 79
: [mm/s] 3 3 30
: OT prewarn false false false false false
: off time 0 0 0 0 0
: blank time 24 24 24 24 24
: hysteresis
: -end -1 -1 -1 -1 -1
: -start 1 1 1 1 1
: Stallguard thrs 0 0 0 0 0
: DRVSTATUS X Y Z Z2 E
: stst * * * * *
: olb
: ola
: s2gb
: s2ga
: otpw
: ot
: C
: C
: C
: C
: s2vsa
: s2vsb
: Driver registers:
: X 0xC
: Y 0xC
: Z 0xC
: Z2 0xC
: E 0xC
: Testing X connection OK
: Testing Y connection OK
: Testing Z connection OK
: Testing Z2 connection OK
: Testing E connection OK

ReplyQuote

Sours: https://reprap.org/forum/read.php?,

Sgen 0 v1 mks l

The morning shower took only one. And it was she who decided to jump on my penis now. Throwing in her leg, she sits down, quickly excites me with a minetik, feeling with her tongue the sour taste of the lubricant of a penis.

MKS SGEN L V1 0

I remembered how we. Started sleeping in the same bed. And every time, after I enjoyed Vlad's ass, she fell asleep, gratefully pressing her cheek to my shoulder.

You will also like:

Wall, pressed it up. Come on. More. More energetically. - she moaned through her teeth, enjoying the caress.



1128 1129 1130 1131 1132