Standard shed double door size

Standard shed double door size DEFAULT

How to Build Double Shed Doors

double shed doorsBuilding Double Swinging Shed Doors

To build double shed doors, here's one of the easiest ways with a step by step guide with illustrations on shed door construction below.

Before you begin any framing for your shed, it's best to decide what size doors you actually need because the framing for the wall containing these doors will have to be framed correctly for this.

For our example to use to explain how easy this really is, I am going to use the following guidelines to build a 5' wide double door for a shed that has a 10' long wall that this door has to be framed into. This is really easy if you are siding your shed with the LP smartside siding panels, or planning on siding over OSB sheets with some sort of lap siding. It doesn't matter.

Ok, lets say with this 10' wall,  you want your door on the right side 1' away from the corner. (this is for illustrative purposes only. You can use any position on the wall you like).

Here's what the framing for this wall will look like with 16" on center wall studs, and the wall is 7' tall. 7' is the typical wall height for a shed.


framing for double shed doorsExample Framing For 5' Wide Double Shed Doors

When it's time to put your siding on whether it be T1-11 or LP smartside siding panels, the next step is to find the exact middle of your door opening. Cut your siding to the desired length or height. Usually this measurement will be so that your siding extends down past the floor by about 2" or so. What ever you decide on this measurement, it should remain the same all around your shed.  In otherworks, the bottoms of all your siding panels will all be even all around the perimeter of your shed.

If you are just using osb, your first osb panel will be attached to the wall framing so that your panel edge is even with your middle of the door mark. To make things easier for you, a temporary board can be nailed on to the rim joist or band board so that your siding panels rest on this board. Nail this panel to the wall framing along the header edge, and the jack stud of the door framing. You won't be nailing into the bottom of this osb panel where the door will be opening.

double shed doorsSiding Placement For First Panel

Using a reciprocating saw you can cut the door panel out from the back side then cut the front section left on the bottom front with a circular saw.

If you plan on building a ramp for your shed, you will want to cut the bottom of your door panel so that it is flush with the top of the floor.

The next panel can now be placed into position so that the overlapping edge is in the right place leaving a gap that is consistent with the grooves in your panels if you have them. Nail this panel to the framing and cut this panel as you did with the first.

double shed doorsSecond Siding Panel Placement

Now both panels have been cut out and your shed wall containing the door opening will look like this:

double shed doors panel placementSiding Panels With Doors Cutout

We have our 5' door opening for double shed doors and we have the two door panels we cut out that we can now build our doors with.

We can start with either panel, it makes no difference. If you decide that you want a shed ramp on this shed, as I mentioned earlier, the panels we have for the doors will have to have the bottoms trimmed off so that the panels when opened and shut will clear the top of the shed ramp.

For this example, we will figure on cutting the panels off for a ramp. This works out to be roughly about 2" off the bottom of each door.

side panels for double shed doorsResulting Door Panels

Working with each door panel individually, we can now frame the outside of these panels with 2x4's and 2x6's as such. These doors will be easier to build using exterior grade 1.5" screws, screwing from the back of the panels into the front 2x4's and 2x6's.

double shed door partsFraming The Outside Of The Door Panels

With the door panels assembled now with 2x4's and 2x6's the shed itself now needs to be framed out with 2x4's and a lentil around the door opening The 2x4's will serve as door jambs and should be screwed or nailed to the frame flush with the door opening.

The door lentil can be made of a 2x6. Mount the jambs on each side so that they extend above the door opening about 1/4". Once the coor jambs are screwed on and in place, your lentil can be nailed into place. With the door jambs extending 1/4" above the door opening, this will allow the doors to swing freely.

double shed doors all framed outDouble Shed Doors Finished

With your doors assembled, now its time to weather proof your hard work. Silicone or latex caulk should be added to all upper horizontal surfaces and all vertical surfaces. If you are using silicone, try to get a paintable silicone. Otherwise your silicone will not take latex based paint and will have to be painted with an oil based paint.

Another option I like to add to my sheds is an angled metal threshold strip on top of the floor right on the front edge. This will help protect your shed floor from wear and tear over the years. This strip can be aluminum and is readily available at your lumber supplier store.

threshold strip for shed doorsProtect Your Floor Edge With Metal Threshold

This metal threshold strip should be pre-drilled and screwed down with exterior pan head screws about 1.5" long every 12" starting from the ends and working your way inward.

How to build shed doors - another way.

Building single shed doors

Leave double shed doors for shedkings home page.

Sours: https://www.shedking.net/double-shed-doors.html

What size is a standard shed door?

Most decent garden sheds will have doors sizes of at least 5ft 6in (168cm) which is more reasonable and some are taller than that. Some manufacturers offer an option for a taller door. To help against the constant moving of the shed door you should ensure three hinges on each door. This will ensure a long life for it.

Click to see full answer.


Herein, how wide can a single shed door be?

Building Single Shed Doors Made Easy. Here's a simple, fast, and very easy way to build your single shed doors up to 36" wide. You could go wider, but any wider than 3' would necessitate the building of double shed doors as the weight would be too heavy.

Also Know, should shed doors swing in or out? follow . 7 best answer: all exterior doors should open out. this is a. but in most public buildings, the entry doors open outward.

Thereof, how wide is a standard door?

Entry doors are usually 36 inches wide.While a door width of 36 inches is oversized for an interior door, it's the standard size for front doors. The standard height remains the same, however, at 80 inches.

How do you measure a shed door?

Measure and mark where the hinges will go on your shed.Use a tape measure and mark 7 inches (18 cm), down, from the top of the door frame and 11 inches (28 cm) up from the bottom of the doorframe.

Sours: https://askinglot.com/what-size-is-a-standard-shed-door
  1. Put item on sale ebay
  2. Audi bay area dealers
  3. Movie sonic vs movie mario
  4. Brothers in arms lyrics
  5. Fated to love you synopsis

Shed Door Plans -Step-By-Step

Below are step-by-step instructions to build a single and double shed door. These shed door plans can easily be customized to fit most sheds.

Shed Door Plans for Single and Double Door

single shed door plans
double shed door plans

 

Shed Door Plans for Single Door

single shed door plans door frame

Begin by framing the door opening, see illustration above for details.

single shed door plans header

The header for the door can be built using 2×4’s or 2×6’s. Cut two 2×4’s or 2×6’s to size, cut a piece of 1/2″ plywood and install between the lumber, see illustration above. Assemble with 3 1/2″ nails.

single shed door plans - siding

 

Install a t1-11 exterior siding sheet over the door opening as shown on illustration above. Secure the siding in place by nailing finishing nails through the siding and into the wall frame.

single shed door plans door opening

Carefully cut out the door opening, the door will be built using the siding that has been cut out.

single shed door plans 2x4 door trim

Measure and cut 2×4’s to go around the door opening. Install the 2×4 trim using finishing nails.

single shed door plans door

Build the shed door with the siding that was cut out earlier in the steps above.

Lay the 2×4’s in a flat even surface, next lay the siding on top of the 2×4’s. Nail 2″ nails through the siding and into the 2×4’s.

single shed door plans hingesAttach the door hinges and install door.

Shed Door Plans for Double Door

 

double shed door plans frame

Begin by framing the door opening, see illustration above for details.

double shed door plans - header

The header for the door can be built using 2×4’s or 2×6’s. Cut two 2×4’s or 2×6’s to size, cut a piece of 1/2″ plywood and install between the lumber, see illustration above. Assemble with 3 1/2″ nails.

 

double shed door plans siding

The double shed door will be built using two t1-11 exterior siding sheets.

Install a t1-11 exterior siding sheet over the door opening as shown on illustration above. Secure the siding in place by nailing finishing nails through the siding and into the wall frame.

double shed door plans cut siding door

Carefully cut out the door opening, the door will be built using the siding that has been cut out.

double shed door plans trim

Measure and cut 2×4’s to go around the door opening. Install the 2×4 trim using finishing nails.

double shed door - door

Build the shed door with the siding that was cut out earlier in the steps above.

Lay the 2×4’s in a flat even surface, next lay the siding on top of the 2×4’s. Nail 2″ nails through the siding and into the 2×4’s.

The T1-11 siding will have a lip that overlaps with the opposite side, leave the siding lip exposed.

double shed door plans - hinges door handle

Attach the door hinges and install door.

Like these shed door plans? Let me know, leave me a comment below. Share this link with your friends and your social media, thanks.

Construct101 offers free online version plans. These free plans also have a free print friendly PDF downloadable version free of ads. Click here to download.

Sours: https://www.construct101.com/shed-door-plans/
Outdoor Workshop Shed - Doors

12×16 Shed Double Door Plans


This step by step diy project is about 12×16 shed roof plans. This is PART 3 of the 12×16 storage shed, where I show you how to build the double front doors. Make sure you check out the first and second part of the project, so you learn how to build the frame of the shed, as well as the roof. You can easily adjust the size and the design of the doors, to suit your needs. Take a look over the rest of my woodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.

 

 

Projects made from these plans

 

 

12×16 Shed Double Door Plans

Building-a-12x16-shed

Building-a-12×16-shed

 

  • I – 2 pieces of 1×4 lumber – 79 1/2″ long, 1 piece – 67″ long, 1 piece of 2×2 lumber – 60″ long JAMBS
  • J – 2 pieces of 1×4 lumber – 70″long, 2 pieces – 30″ long, 1 piece – 23″ long, 1 piece of T1-11 – 30″x77″ 2xDOOR

 One day

 

 

Building double shed doors

Fitting the door stop

Fitting the door stop

The first step of the project is to build the door stop for the 12×16 shed. Cut the door stop from 2×2 lumber and secure it to the top header with 2 1/2″ screws. Drill pilot holes through the lumber before inserting the screws, to prevent the wood from splitting.

Fitting-the-door-jambs

Fitting-the-door-jambs

Fit 1×4 trims around the door opening. Cut the components at the right dimensions and secure the jambs into place with 1 5/8″ brad nails. Align the edges flush.

Building-the-shed-doors

Building-the-shed-doors

Continue the project by assembling the double shed doors. Cut the frame of the 1×4 lumber at the right dimensions and lock them into place with 1 1/4″ nails and construction glue. Align the edges flush and make sure the corners are square.

Fitting the doors

Fitting the doors

Fit the double shed doors to the opening and lock them to the jambs with hinges. In addition, install a latch to keep the doors shut.

Front double doors

Front double doors

This 12×16 storage shed has a nice design and the wide front doors make it easy to have access. In addition, you can easily adjust the design of the shed and fit another door to the side wall.

How to build a 12x16 shed

Make sure you consider fitting decorative 1×4 trims to the corners of the shed and to the all sides, in order to enhance the look of the project. Moreover, fit the soffit and a vent to the shed. Apply a few coats of paint to enhance the look of the shed and to protect the surface from decay and water damage.

12x16 Shed Plans

12×16 Shed Plans

Make sure you check out the rest of the project, so you learn how to frame the 12×16 garden shed and how to build the gable roof. In addition, I have lots of other shed projects on the site so I recommend you to browse through all alternatives before starting the building project.

 

 

This woodworking project was about 12×16 double shed door plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

 

Previous

 












Sours: https://myoutdoorplans.com/shed/12x16-shed-double-door-plans/

Size door shed standard double

2392shares

I’m often asked how to build double shed doors. It’s easier than you think, and the design has been used for thousands of years. Ready-made planks, screws, nails, and steel hinges, however, make it easier than wooden pegs, twine, and leather hinges.

Whether at the design or finishing stage, a door is an important consideration. It provides access, security, and an aesthetic touch. You need to determine what size of door you need, and what has to fit through it. Does it need to fit your width, a lawn tractor, or something larger?

You could buy a door, but the look of a door you’ve crafted on a shed you’ve built is a statement of pride and craftsmanship for all to see. I like batten doors. They can be trimmed to fit any opening, are easy to build, provide security, and they look great. In this article, I’ll explain how to build double batten shed doors, with lots of pictures too! If you only need one door, then adjust the plan and make only one.

Quick Navigation

 How to Build Double Shed Doors

 

Types of Shed Doors

There are hundreds of doors available on the market today, and many plans for doors you can build. Here are several types more common on sheds.

Batten Door

Batten shed doorsThere are 3 types of batten doors made with vertical planks.

(1) Three horizontal planks or ledges hold the planks together and provide backing to hinges.

(2) Adding a diagonal brace between the ledges from the outer top to inner bottom helps prevent door sag.

(3) To further strengthen the door, add a second vertical plank to frame the inside front and back edge of the door.

 

 

Dutch Doors

Dutch doorA Dutch door is one that has been cut horizontally in half (or slightly larger on the bottom than top). The bottom portion can be left closed to prevent movement in or out while the top is open to provide light and airflow.

 

 

Hinged Swinging Door

A hinged door may swing into or out from a structure, so it requires space to swing. The number of hinges on a door depends on the weight and size of the door.

Pros

  • Easier to install
  • Give up less wall space
  • Hardware costs less
  • Close more tightly (cold climate)
  • More secure

Cons

  • Must be fitted to the frame
  • Requires swing space

Sliding Shed Doors

Sliding shed doors are like sliding barn doors. Rollers are attached at the top that fit into a rail secured to the shed. They are opened by pushing them to the left or right of the doorway (sometimes both directions).

Pros

  • Easy to build and install
  • Easy to operate
  • Doesn’t take up much space

Cons

  • Harder to lock
  • Trickier to seal
  • Loose wall space

Roll-Up Shed Doors

Roll-up doors are similar to what rental storage units have. They have two side guide rails and roll up into a canister or spool at the top. You can make your own, or purchase one ready-made.

Pros

  • Require no space to swing or slide
  • High security
  • Convenient in use

Cons

  • Heavy to install
  • Pre-set sizes
  • Looks manufactured

Glass or French Doors

Installing sliding glass doors or swing French doors are another option, especially if the shed needs more light or will be used as a backyard office or she-cave.

Popular Materials for Shed Doors

Different materials can be used to make shed doors. The dimensions of the project may also influence the materials used. My preference is T&G pine planks, but I’ve used other products too.

Tongue and Groove Wood Boards

Tongue-and-groove boards

Tongue and groove planks have a groove cut into one edge and a tongue cut out on the other edge. The tongue of one board is pushed into the groove of the plank next to it. The T&G help secure the pieces together, reduce warping, and prevent gaps due to shrinkage. You can make T&G boards, or purchase them pre-made.

Pros

  • Easy to use
  • Looks good
  • T&G reduce gaps
  • Stain, paint or varnish it

Cons

  • Expensive in some areas
  • Must be sealed on all surfaces
  • May warp

Price Range: 1”x6” pine is $1 – $1.50 (US) per linear foot

T1-11 Siding

T1-11 Siding

T1-11 is made of thin layers of wood veneer (plywood) or strands (OSB) that are glued, heated and pressed together before being trimmed to size. The exterior grade 4’x8’ sheets have grooves cut every 8”, so they look like shiplap or T&G.

Pros

  • Inexpensive batten look
  • Paint or stain
  • No gaps between boards
  • Weathers better than planking

Cons

  • Can flake, split or rot
  • Requires maintenance
  • Can warp

Price Range: ½”x4’x8’ sheet is $30.00 – $40.00 (US)

LP SmartSide Panel

SmartSide is an example of engineered wood. The 3/8”x4’x8’ panels look like T1-11 OSB. The strands are infused with zinc borate before being coated with a marine wax and resin glue mix, and then pressed and heated together. The sheets are given a protective tan colored resin-saturated overlay.

Pros

  • Critter, bug, moisture, and rot resistant
  • Environmentally friendly construction
  • Pre-primed, so paint any color
  • 50-year warranty

Cons

  • All cuts need to be sealed
  • Requires periodic painting
  • May warp
  • Dulls saw blades and drill bits

Price Range: 3/8”x4’x8’ panel is $30.00 – $40.00 (US)

Grooved Plywood

Grooved Plywood

Thin layers of wood veneer glued, heated, and pressed together and cut into 4’x8’ sheets of different thicknesses. The panels are then grooved by a router to look like battens. It is not classed as an exterior grade but can be used outdoors. Available in ‘U,’ channel, and reverse board and batten grooved sheets.

Pros

  • Opposing layers of grain make it very strong
  • Won’t shrink or warp
  • Can be painted or stained
  • Multiple thicknesses available

Cons

  • Susceptible to water damage, rot, and layer separation
  • Needs to be painted and maintained
  • Porcupines and squirrels like to chew on it

Price Range: 4’x8’ panel is $30 – $60 depending on thickness and veneer

 

Several Configurations Before You Start

Some sheds are still used for the purpose they were originally built. Others have gone through transitions from storage to garden, to a playroom, or an office or craft room. Most sheds will last for decades if maintained.

  1. Decide on the width and height of the door
    The door dimensions are usually based on what the shed will be used for, and should be determined before building. A standard 36” x 80” door is easier to carry boxes through than a 32” wide door; however, a lawn tractor fits through a 48” door better. The door height may influence, or be influenced, by the height of the wall into which it fits.Plan for today, but build for tomorrow. Put a 6’ or 8’ header in if you can. You can still frame for a 3 or 4-foot door today, but later, on a wider door configuration may be more useful.
  1. Decide whether you need a single or double door
    Based on the dimensions needed for the use you have planned for your shed; decide if you want a single or a double door. A 36” door is best for human movement, 48” or wider for lawn tractors and trailers.Double doors offer a versatility many don’t consider. They can both be the same width, or you can play with the dimensions. If you only need a 48” wide door occasionally, split the opening to be 36”-12”. The same can be done for a 60” opening, so you have the 36” passage, and a 24” fixed with a top and bottom bolt until the wider is needed.
  1. Choose between a hinged swinging door and a sliding door. Once the door size is determined, decide if you want a hinged or sliding door arrangement. Two doors can be hinged to swing from opposite sides of the door frame, or bi-fold hinged to swing from only one. Sliding doors need space to slide open and may require planning at the design stage. Large sliding doors sometimes have a passage door built into them too.
  1. Decide if you want door blend in with the shed or to stand out.
    The last consideration is aesthetics. Will the door blend with the shed siding, or will it be a bold statement. It’s an individual decision, but an important one.

How to Build Double Shed Doors – Step by Step Instructions

There are different ways to construct batten doors. Batten doors are easy to build, adjustable in size, and look great. I’ll show you how I build them with step-by-step instructions, including helpful pictures.

Over the past few years, I’ve built 3 sheds with double swinging batten doors:

My first was a small Gable shed.

Building double shed doors

The second shed I built was a larger Slanted Roof Shed.

Double shed doors

Like many of you, I needed more space and added a lean-to shed on the end of my second shed. I used the batten process to make a double swing shed door for it too.

Main Components of a Batten Door

There are three parts to my ledged and braced batten doors. The vertical boards or battens for the door panels, three horizontal rails or ledges, and two diagonal pieces or braces.

Main Components of a Batten Shed Door

Shed Door Design

My preference is tongue-and-groove 9/16” x 6” x 8’ (real size – 9/16 x 5-¼) pine boards for the battens. They’re available from most lumber supply stores. I buy them in bundles of 4 boards.

The door opening, after it’s been finished and trimmed, is 40-¾” x 68”. The plan is to make two 20-¼” x 68” door panels. The extra ¼” will allow for expansion between the panels.

Each door is held together by three 2×4 rails or ledges, and two 2×4 diagonals or braces. That is why they are called ledged and braced batten doors. If the roof has an overhang, make sure it doesn’t interfere with the doors opening or closing.

Measure the Door Opening

After the door opening has been framed and trimmed, measure the size of your shed door frame.

Measure the Door Opening

 

Choose and Purchase Materials

The width of the door opening helps determine the amount of wood required for the doors. If each door panel is 20-¼” wide, and my preferred pine plank is 5-¼” wide, I’ll need 4 planks. I bought 1 package extra so I could choose better boards. Select good boards – choose straight boards with fewer knots.

Door boards

Prepare Door Boards

Prepare Door Battens

Cut the planks to the length needed. For each door, I cut 4 T&G boards to 68” long. I then ripped off the tongue from one plank, and the groove from another using a table saw.

Remove the tongue on one plank.

Rip the tongue off board

Rip the groove off another board.

Rip groove           

Dry Fit and Glue the Doors

Lay the boards on a workbench or a pair of sawhorses with the outside face down.

Lay door boards with face down

 

To minimize cupping and warping, try to mix the planks, so the end grain curvature alternates in and out. The ledge and brace boards will prevent cupping, but alternating further reduces the risk. You may want to do this before trimming the tongue and groove in the step above. I wasn’t able to this in my last door, which is why I bought extra planks.

dry fit door boards

Here’s another example:

Alternating pattern to minimize cupping

The end grain close up shows the alternating pattern to minimize cupping as the wood ages and weathers.

Dry fit the door boards to make sure that all tongue and groove joints fit.

Dry fit boards

Apply a light bead of wood glue on one side of the groove of the first board.

Some people are against gluing T&G boards saying it restricts the board from expanding and contracting. By applying the binder to one side of the groove, the board is free to expand or contract. Additionally, shrinkage or expansion doesn’t occur only at the edge; it is across the board.

The best way to limit the movement within the wood is to seal (paint, stain, and urethane) all 6 faces of the plank to control moisture. If you’re nailing it or screwing it to the ledges, the movement is restricted even more. The glue is sealing the joint, as well as securing the edges together. After 4 years on rain, snow, strong winds, my batten doors are still strong, clear of splits or cracks, and flat.

Apply glue on board groove

Repeat for all boards and join them into the grooves to help spread the glue some. Wipe off any that squeezes out.  Align all ends flush.

Join boards

Make sure first, and last boards are square at the edges. I use a large carpenter’s square or a sheet of plywood with true corners and edges.  

Clamp the boards together but do not overtighten. You want enough pressure to close the joints completely, but no more. Recheck to make sure the outer edges are still square.

Clamped boards

Clean off any excess glue that has squeezed out of the joints.

Cut 3 horizontal rails or ledges 18” long from 2×4 boards for each door panel. I bevel cut mine at one end. The hinge end remains square.

Cut and Attach the Rails or Ledges

Cut battens

Sand the pieces with 120 grit sandpaper. I use a random orbital sander.

Mark the location of the top rails on the batten panels. Mine is 7” from the top and 1” from door sides.

Mark batten location

 

Apply construction adhesive to the back of the top rail or ledge.

Apply construction glue

Attach the rail to the boards with 2” decking screws.

I decided to build this door slightly different from the others I made for my other sheds. I choose to run all screws in from the back through the 2×4 ledges into the door battens. This way the outside face of the door would look better, and I’d have less issue with screw heads being visible when I paint the door. The downside is I’ll be attaching thicker 2x4s to thinner 1×6 boards while knowing it is better to attach thin boards to thicker.

Attach batten to board

Mark the location of middle ledges down 22” from the bottom of the top ledge, and 1” from door sides. Apply construction adhesive to the back of the 2×4 pieces, and attach to the door battens with 2” decking screws.

Mark the location of bottom batten 7” up from the bottom of the door, and 1” from door sides. Apply construction adhesive to the back of the 2x4s, and attach to the door panes with 2” decking screws.

With the ledges screwed to the door battens, remove the clamps.

Completed right door panel

Cut two 2×4 pieces for each door panel to fit diagonally between the ledges for the braces.

Cut door braces

 

Apply construction adhesive to the back of the first, fit it from the bottom to the center, and attach to the board with 2” deck screws

Glue door braces

Apply construction adhesive to the back of the second, fit from the center to the bottom, and attach to the board with screws too.

Attach braces

 

Trim Off One End

I built my doors to the dimensions of the passage opening, which meant there was no gap and the doors would stick. Draw a line ⅛ – ¼” across the top or the bottom, not both. That will allow a gap for opening and closing.

I cut with a circular saw using a guide to keep it straight.

Sand the doors with 120 grit sandpaper. I use a random orbital sander.

Completed double doors

 

Priming and Painting

Apply a good exterior wood primer to all surfaces. Remember the top and bottom of the doors too.

Priming doors

Use an exterior latex paint of good quality to cover all surfaces, including the top and bottoms of both panels. It’s better to use semi-gloss or gloss paint. I use a brush and a sponge roller.

Painted doors

How to Frame a Shed Door Opening

A door may seem like just a hole in the wall, but it is a reinforced hole. It requires additional support to carry and spread the weight of the wall and roof above and to maintain the structural integrity of the wall itself.

King Studs: Frame the opening at each side and go from the bottom plate to the top plate.

Jack Studs: Studs shortened to the height of the door opening plus 2-inches (usually). They support the header.

Header: Carries the weight of the building above the door opening. Dimensions depend on the size of the opening. Often two 2×4 or 2×6 on edge with spacer shims or ½” plywood sandwiched between.

Shed Door Opening

Cripple Studs: Short studs that fit between the top of the header and the bottom of the top plate. They are usually placed to continue the 16” or 24” center pattern of framing studs, with one directly above each Jack stud.

Door header components

My header is two 2x4s with a ½” OSB strip sandwiched between to match the 3-½” thickness of the studs.

Assembling door header

I framed my door opening with the King Stud sandwiched between a stud and the Jack Stud. I also didn’t have space for any Cripple Studs above the header.

How to Frame a Shed Door Opening

How to Choose Hardware for Shed Doors

There are dozens of types of hinges available today made of different metals, finishes, and styles; some are even made of wood. However, they all secure a door to a frame so it can pivot and open or close.

The height, width, thickness, and weight of a door are factors to consider when selecting hinges. Doors less than 60-inches usually have two hinges; add one for every 20-inches of height above that. Hinges are available for different door thicknesses; pick one that is rated for the door dimension. Weight can over-ride height on the number of hinges. Use two hinges for panels up to 20-pounds, three up to 40-pounds, and four up to 60-pounds. Extend the pattern if the door is heavier.

Hinges

For my door I used Strap or T-Hinge hardware. It mounts to the outside of the door since it doesn’t have a proper frame for a Butt Hinge. The T-Hinge is rated for light, medium and heavy doors, so pick the one best for your project.

How to Choose Hinges

I used 8-inch spring loaded T-Hinges. The spring can be adjusted to help close the door, so it doesn’t swing in the wind.

Door hardware

 

How to Secure Double Shed Doors

Hinges should be 5” or more from the top and bottom of the door. Mine are centered on the ledges, so about 8-½” from the top and bottom. Leave a 1/4″ to 3/8” gap for seasonal expansion between the frame and the door.

For added security, I replaced two of the supplied screws with a carriage bolt on each hinge.

Door Hinges

Clamp to door panel into place, and mark the location – make sure the hinges are level. Make sure to keep the 1/4” to 3/8” gap. I clamp to the top and bottom plates – this is why I didn’t cut the bottom plate out yet.

Clamp to door panel

Drill the holes for carriage bolts (one per hanger), and install the bolt and screws. You may want to drill a smaller guide hole for the screws to prevent splitting. I find it easier on my back to lay the doors on portable saw horses.

Install hinges

I finger-tighten the carriage bolt until the screws are in place, then flip the door and tighten with a wrench.

Tighten the carriage bolt

The door is ready to hang once the two hinges are in place.

Hinges installed

Drill the hole for the carriage bolt in the door frame. It will go through the stud framing, so have a bolt the correct length.

Secure the hinge to the frame

Secure the hinge to the frame with the carriage bolt. I only finger tighten the nut until both hinges are in place.

Fasten hinges

Once both hinges are in place, screw the other fasteners in, and wrench-tighten the bolts.

Door installed

If the bolt is too long, it can be cut off, or used for hanging a jacket on.

Tighten the bolt

Repeat the hinge process for the second door. Remember to cut out the bottom plate once both doors are installed.

Shed double doors installed

I attached a gate latch to keep the doors closed. It’s level with the top hinges, so the screws bite into the 2×4 ledge.

Two ring bolts are attached into the middle ledge board. They allow the doors to be locked and also act as pull knobs for opening.

Conclusion

Building and installing batten doors in a shed you’ve built is like icing to a cake. It finishes it off and looks awesome. Hopefully, my article was helpful. Your feedback is appreciated, and if you know someone who may find the instructions of use, pass it on.

Eugene

Eugene Sokol

Eugene has been a DIY enthusiast for most of his life and loves being creative while inspiring creativity in others. He is passionately interested in home improvement, renovation and woodworking.

Sours: https://plasticinehouse.com/how-to-build-double-shed-doors/
How To Build A Shed Door

The door dimensions are usually based on what the shed will be used for, and should be determined before building. A standard 36” x 80” door is easier to carry boxes through than a 32” wide door; however, a lawn tractor fits through a 48” door better.


Click to see full answer

Just so, how wide can a single shed door be?

Building Single Shed Doors Made Easy. Here's a simple, fast, and very easy way to build your single shed doors up to 36" wide. You could go wider, but any wider than 3' would necessitate the building of double shed doors as the weight would be too heavy.

Furthermore, should shed doors swing in or out? follow . 7 best answer: all exterior doors should open out. this is a. but in most public buildings, the entry doors open outward.

Then, what size should a shed door be?

Most decent garden sheds will have doors sizes of at least 5ft 6in (168cm) which is more reasonable and some are taller than that. Some manufacturers offer an option for a taller door. To help against the constant moving of the shed door you should ensure three hinges on each door.

How much gap should be around a shed door?

There should be 1/4″ on all sides of the inner door frame between the door frame and the door opening inside of the shed. Check the fit of the plywood outer face of the door against the siding on the shed. There should also be a 1/4″ gap on all sides on the outside.

Sours: https://findanyanswer.com/how-wide-are-double-doors-on-a-shed

Similar news:

Shed Double Door DIY Plans

Shed Double Door Plan Library

 

Overview

This is a simple method to construct a sturdy and lightweight double shed door. The door height and width can be easily customized per shed size as needed. See instructions here for single shed door plans. This door build fits all shed designs, check out our Shed Plan Library!

Want to add a single door to your shed? Check out our Single Door Plan.

 

Material and Cut List

 

DOOR FRAME
2 – 2 x 4 Lumber: 6′-3 1/2″
6 – 2 x 4 Lumber: 7 1/2″
2 – 2 x 6 Lumber: 6′-3″ (door header)
1 – 2 x 6 Plywood Filler: 6′-3″ (door header)
1 – 2 x 6 Lumber: 6′-7″ (door trim)
2 – 2 x 4 Lumber: 6′-5″ (door trim)

DOOR
4 – 2 x 6 Lumber: 3′
2 – 2 x 6 Lumber: 2′ 5″
4 – 2 x 4 Lumber: 5′ 6″
2 – 4′ x 8′ Plywood Siding Panel T1-11: 6′-5 3/4″ x 3′-0″

HARDWARE
2 – Door Handle or Latch
6 – 3-1/2 in. x 5/8 in. Door Hinge

 

Step 1 – Door Framing

Start with building the door frame opening as illustrated below. Make sure the edges of the studs and header are perfectly flush, measure and adjust as needed.

Cut two 2 x 4 lumbers to 6′ 3 1/2″ length for jack stud.
Cut two 2 x 4 lumbers to 7′ 7 1/2″ length for king stud.
Cut two 2 x 6 lumbers to 6′ 3″ length for door header, use a 1/2″ plywood as filler in-between.

Then, drill pilot holes and insert 2 1/2″ screws every 10″ to secure everything.

Double Shed door framing plan

Both 2 x 6 or 2 x 4 lumbers will work for the header, for larger doors I would recommend 2 x 6’s. Cut the 2 x 6 and 1/2″ plywood filler to length, then assemble with 3 1/2″ screws every 8″.

double shed door header detail

Step 2 – Add Exterior Siding

After the wall frame is set in place, install the T1-11 exterior siding panel with 2 1/2″ nails every 8″. The bottom of the siding should be at least 1″ below the bottom plate, this is to cover the gap between the wall frame and foundation.

Measure and cut out the door opening, use the jack stud framing as the guide. You can use a Sabre saw to cut through T1-11 fairly easily.

double door siding plan

Step 3 – Install Casing

Cut a single 2 x 6 lumber to 6′ 7″, and cut two 2 x 4 lumber to 6′ 5 3/4″.

It’s important for the casings to flush with the door opening, so the door opens and closes smoothly. Drill pilot hole and insert 3 1/2″ screws to secure in place.

double door casing DIY plan

 

Step 4 – Door Construction

Finally, time to work on the actual doors! First, measure the door opening again to confirm height and width, sometimes this can change slightly from craftsmanship. Cut out both doors to size from a single piece of T1-11 exterior siding panel. Hold them up to make sure they fill the entire door opening without any sizable gaps.

Materials for one door: cut two 2 x 6 lumbers to 3′, cut a single 2 x 6 lumber to 2′ 5″, and cut two 2 x 4 lumbers to 5′ 6″.

Place trims flat onto the siding panel to ensure they are square. Then drill pilot holes and insert 2″ screws to secure in place. Repeat for the second door.

double door build DIY plan

 

Step 5 – Hanging the Door

With both completed doors in closed position, use a pencil to mark up the metal hinge locations on both the door and the casing. Make sure the hinges are straight, yielding a smoother swing.

Attach the hinges onto the door with screws first. Then lift the door in place at closed position, screw in the hinges onto the casing. Swing the door to test out alignment, adjust as needed. Repeat for the second door.

completed double shed door plan

 

It is also recommended that you add a door stopper to prevent the doors from swinging into the shed. With the doors in closed position, attach any small piece of wood block (1 x 1) under the header. Make sure it’s tight against the back side of the doors in closed position, this will get the doors to close perfectly.

double door DIY 3D

 

And that’s it, your double shed door is complete! If you’d like to get fancy, try some of the bracing trim patterns below:

double shed door trim variations

 

3D View of Double Shed Door Assembly

 

3D view of shed door

Sours: https://buildblueprint.com/shed-double-door-plan/


369 370 371 372 373